Third Brake Lights for 356, 912 and 911 Porsches

Coupe Version

Click image to enlarge wiring instructions

The coupe version is a module 6 inches wide, ½ inch high and ¾ inch deep. The housing is made of plastic extrusion and painted black. It mounts inside of the car at the top of the rear window. The installation is simple and straight forward. The housing has an attached mounting flange which slips over the rubber window seal. No holes to drill!
The wiring is routed inside the car ending at the brake light switch. Wiring instructions and all of the necessary wire, connectors and wiring accessories are furnished. Typical installation time is about 2 hours. Tools required are a pair of pliers and a screw driver.

Coupe Twin Lights Version

Click image to enlarge wiring instructions

These Lights may be wired to function as Brake Lights, Tail Lights or Turn Signal Lights.
The Twin Lights are modules 2 3/4 inches wide, ½ inch high and ¾ inch deep. The housings are made of plastic extrusion and painted black. They mount inside of the car at the top of the rear window. The installation is simple and straight forward. The housings have an attached mounting flange which slips over the rubber window seal. No holes to drill!
The wiring is routed inside the car ending at the master cylinder brake light switch, rear tail light or the front turn signals. All of the necessary wire, connectors and wiring accessories are furnished alog with detail instructions. These Lights may be wired to function as Brake Lights, Tail Lights or Turn Signal Lights.

Behind the Grill Version

Click image to enlarge wiring instructions

The behind grill version is a sealed module 6 inches wide, ½ inch high and ¾ inch deep. The housing is made of plastic extrusion. It mounts behind the grill either at the top center of single grill cars or the top center of the left grill on dual grill cars using a supplied mounting bracket. The bracket is held in place by mounting between the grill an the deck lid. No holes to drill!
The wiring routes out of the engine compartment, beneath the car and into the car's interior at the opening of the shift mechanism then within the car to the brake light switch. Wiring instructions are furnished along with all of the necessary wire, connectors and wiring accessories. Typical installation time is about 2 hours. Tools required are a pair of pliers and a screw driver.

Twin Lights Behind the Grill Version

Click image to enlarge wiring instructions

These Lights may be wired to function as Brake Lights, Tail Lights or Turn Signal Lights.
The Twin Lights are assembled using 12 bright LED’s each, mounted within a plastic housings measuring three and ½ inches long, ½ inch high and ¾ inch deep. They mount on each side of the grill(s) are held in place by the mounting between the grill and deck lid. (3 inches distance between the top of the grill to the inside panel is required.) The wiring is routed to the master cylinder brake light switch, rear taillight or the front turn signals. Typical installation time is about one and ½ hours. Tools required are a pair of pliers a screwdriver and a wrench for grill removal.

Third Brake Light Flasher Unit

Adjusts from full on or 2-20 flashes /second.

Works with 6 volts or 12 volts.

Size: 1 1/4 inch square X 7/8 inch high X 3/8 oz.

Unit will support up to 2 Light products.

Wiring Instructions:

1. Unit placement:

Locate the wire which is connected from the master cylinder brake switch to the Third Brake Light.

Pick a location near the wire run for the flasher placement.

Keep in mind that you might want to easily adjust the flashing frequency.

Cut the wire into.

2. + Voltage wire routing of the Third Brake Light:

Connect the wire end from the master cylinder brake light switch to the appropriate connection on the flasher unit.

Attach the wire end from the Third Brake Light to the appropriate connection on the flasher unit.

Wrap each connection with the supplied electrical tape.

3. Chassis ground wire routing from the flasher:

Route the black ground wire from the flasher unit to a chassis mounting fastener and attach the ring lug.

Clean the chassis surface around the fastener area.

Place the ring lug between the chassis and fastener and tighten.

4. Check for functionality and set the desired interval.

Our lights mount onto 356, 912, 911, 914 cars.

All versions are available in 6 volt or 12 volt

These instructions are supplied to explain how to mount and wire a 356 Coupe version light into a 912, 911, and 914. Included are special connectors which facilitate wiring.

Universal Light Bar Version

The Light Bar is an assembly of 27 bright red LED's and 9 resistors mounted onto a custom printed circuit board. The assembly measures .20 inches thick x .55 inches deep x 5.60 inches long.